extractor tool for crimp terminals order no : ats - 638 2446 00 release date: 0 6 - 18 - 15 uncontrolled copy page 1 of 3 revision: a revision date: 0 6 - 18 - 15 extractor tool application tooling specification s heet order no. 63824 - 46 00 features ? the 63824 - 46 00 extrac tion tool is designed to remove crimp terminals from nano - fit? power connectors . see below. scope products : nano - fit ? p ower c onnectors and crimp term inals 2 0 - 26 awg. terminal series no. terminal order no. housing series no. housing order no. 105300 20 - 26 awg nano - fit? 105300 - 1100 105300 - 1200 105300 - 1300 105300 - 2100 105300 - 2200 105300 - 2300 105307 105307 - 1102 105307 - 1103 105307 - 1104 105307 - 1105 105307 - 1106 105307 - 1107 105307 - 1108 105307 - 2101 105307 - 2103 105307 - 2104 105307 - 2105 105307 - 2106 105307 - 2 107 105307 - 2108 105308 105308 - 1102 105308 - 1103 105308 - 1104 105308 - 1105 105308 - 1106 105308 - 1107 105308 - 1108 105308 - 2101 105308 - 2103 105308 - 2104 105308 - 2105 105308 - 2106 105308 - 2107 105308 - 2108 with tpa feature 105307 105307 - 1202 105307 - 120 3 105307 - 1204 105307 - 1205 105307 - 1206 105307 - 1207 105307 - 1208 105307 - 2202 105307 - 2203 105307 - 2204 105307 - 2205 105307 - 2206 105307 - 2207 105307 - 2208 105308 105308 - 1202 105308 - 1203 105308 - 1204 105308 - 1205 105308 - 1206 105308 - 1207 105308 - 1208 105 308 - 2202 105308 - 2203 105308 - 2204 105308 - 2205 105308 - 2206 105308 - 2207 105308 - 2208 description: this extractor tool is 57.3 mm (2. 26 in.) long by 6.35 mm (. 25 in.) diameter, and weight about 0.03kg (1 oz.). see fig ure 1 . tpa latch before terminals can be extracted the tpa latch must be opened first on nano - fit? power connectors that have the tpa feature see chart above . 1. using a small screwdriver insert the flat edge under the tab of the tpa lock. see figure 2 . 2. pull up and push out towards the crim ped wire. 3. repeat this on the opposite side of the tpa lock . the tpa lock should be removed completely from the power connector. 12.7mm 0.50 44.5 mm 1.75 57.3mm 2.26 figure 1
extractor tool for crimp terminals order no : ats - 638 2446 00 release date: 0 6 - 18 - 15 uncontrolled copy page 2 of 3 revision: a revision date: 0 6 - 18 - 15 slot in the connector figure 3 extractor tool nano - fit connector wire tpa in locked position figure 2 insert the screwdriver under the tab nan o - fit connector crimped wire tang in the terminal figure 4 extractor tool housing terminal push crimped wire operation: when removing a damaged crimped wire from the nano - fit? power connector follow the steps below: 1. position the bl ade of the extraction tool into the slot (in line with the crimped terminal to be removed) in the front face of the housing as shown in figure 3 . 2. push the terminal forward in the arrow direction before using the extractor tool as shown in figure 4 . 3. insert the extractor tool into the slot of the connector housing . push extractor tool into the slot until it clicks or comes to a stop. do not force the extractor tool any farther, otherwise it may damage the housing. 4. depress the terminal tang and push the terminal back through the connector slot.
extractor tool for crimp terminals order no : ats - 638 2446 00 release date: 0 6 - 18 - 15 uncontrolled copy page 3 of 3 revision: a revision date: 0 6 - 18 - 15 extractor tool figure 5 nano - fit connector crimped wire 5. holding the extractor tool against the housing, gently pull the crimped wire out of the connector. see figure 5. note: when a terminal is removed in this manner the locking tangs are damaged and the terminal is not reusable. caution : this extractor tool should be used to extract the terminal or seal cap only. using it for unintended purposes may cause injury or damage to parts. be careful not to deform the end of t he terminal. avoid lifting the housing lock too high. caution : molex specifications are valid only when used with molex terminals, applicators and tooling. molex does not offer repair parts for extractor tools due to the inexpensive nature of these too ls. contact information for more information on molex application tooling please contact your nearest molex location shown below. visit our web site at http://www.molex.com
|
